Topic Options
#74121 - 11/08/19 09:25 AM Gimbal Expansion joints Arrangement
NRAM Offline
Member

Registered: 01/31/12
Posts: 60
Loc: Malaysia
Dear Friends,
I'm working on a ducting system with a design temperature 500C and OD 1400mm that is an inlet of equipment with a diameter of 17m and an average temperature of 550-600C. I have designed this line with 2 gimbal expansion joints as attached file. Is it a correct design? Is this system well-arranged for absorbing the radial movement of equipment and absorbing the vertical movement of the duct(22m vertical line)?
Do two expansion joints withstand 7m spool between them?
Regards,


Attachments
Inlet Ducting.jpg


_________________________
Regards,

The shortest answer is doing

Top
#74122 - 11/08/19 11:46 PM Re: Gimbal Expansion joints Arrangement [Re: NRAM]
Sigma Offline
Member

Registered: 10/22/06
Posts: 37
Loc:

1. If possible orient horizontal leg perpendicular (appears at 45 Deg to me) to nozzle axis to absorb radial movement from nozzle and vertical expansion.
2. I hope you have started with simple EJ such as tied universal etc. prior to using 2 Gimbal EJ's
3. For the 7m spool between EJ's, you may provide a spring support.
4. What are the restraints in the vicinity of EJ?

Top
#74123 - 11/09/19 02:03 AM Re: Gimbal Expansion joints Arrangement [Re: Sigma]
NRAM Offline
Member

Registered: 01/31/12
Posts: 60
Loc: Malaysia
Dear Sigma,
Thanks for your reply.
1-The equipment is installed in the field and I cannot change the orientation of the nozzle.
2- WIth using tied universal EJ, moments on the expansion joint is about 10 and 9 ton.m in My and Mz. Is it Ok for the Universal EJ? (It should be mentioned that overall lateral movement of expansion joint due to equipment and vertical line movement is 200mm)
3- Is it reasonable to report loads on two gimbal expansion joints to the EJs' vendor?
4- Spring support with guide support.
_________________________
Regards,

The shortest answer is doing

Top
#74126 - 11/11/19 03:53 AM Re: Gimbal Expansion joints Arrangement [Re: NRAM]
Sigma Offline
Member

Registered: 10/22/06
Posts: 37
Loc:
If the radial expansion is relatively smaller(<<< vertical), then in present 45deg configuration, I believe the 2-Gimbal EJ arrangement can absorb radial expansion from the equipment, although somewhat less effective than had the horizontal spool oriented 90deg to nozzle axis. Are Caesar-II results any different?

200mm of lateral movement would result in ~1.64 Deg of rotation for each bellow (with 7m pipe spool in between) and should not be an issue to EJ vendor. Please show restraints local to EJ in the datasheet (a small sketch for better understanding), so that the EJ vendor can review the adequacy of supports.

And yes, those external piping loads (over and above the pressure thrust loads) should be sent to EJ vendor for proper design of external hardware.

Top
#74144 - 11/13/19 12:38 AM Re: Gimbal Expansion joints Arrangement [Re: Sigma]
NRAM Offline
Member

Registered: 01/31/12
Posts: 60
Loc: Malaysia
The radial expansion of equipment is about 90mm, and this movement causing the lateral movement in two gimbal expansion joints assembly and pushing them along the horizontal line.
Another question:
Is a 3 gimbal expansion joints route a stable system? please see attached file. Two gimbal expansion joints are in a leg that has an angle in x-y and z-y direction. Line temp= 500C,
The right equipment movements: vertical movement=230, x and z direction: 50~60mm
EJ No. 1= Simple(fabric), No.2,3,4 =Gimbal
I think another solution for this route is using tied universal EJ with 2 rods(for having the lateral and angular movement in this EJ)instead of EJ No.4. I would greatly appreciate it if you kindly give me some advice.


Attachments
3g.jpg




Edited by NRAM (11/13/19 12:51 AM)

Top
#74145 - 11/13/19 02:59 AM Re: Gimbal Expansion joints Arrangement [Re: NRAM]
Sigma Offline
Member

Registered: 10/22/06
Posts: 37
Loc:
IMHO three Gimbal EJs in series would be too much and would not be stable arrangement. Better discuss with seniors/EJ supplier.

Top
#74146 - 11/13/19 07:01 AM Re: Gimbal Expansion joints Arrangement [Re: NRAM]
Sigma Offline
Member

Registered: 10/22/06
Posts: 37
Loc:
Further to add. Are you sure about use of Simple(fabric) EJ-1 at Line temperature of 500 DegC you mentioned above???

Top
#74153 - 11/13/19 04:30 PM Re: Gimbal Expansion joints Arrangement [Re: NRAM]
Michael_Fletcher Offline
Member

Registered: 01/29/10
Posts: 816
Loc: Louisiana, US
3 joints in a row is possible (here's a diagram, but with ball joints).
https://www.hyspan.com/BarcoBall.html

However, you have to have a system that's protected from the effects of gravity causing the segments between joints from slumping over.

In the diagram on the site, you should assume that the pipe is in the horizontal, and that the hole thing is universally supported, and that the make-up the ball joints perform is exclusively in the horizontal plane.

Top
#74154 - 11/13/19 05:49 PM Re: Gimbal Expansion joints Arrangement [Re: Michael_Fletcher]
NRAM Offline
Member

Registered: 01/31/12
Posts: 60
Loc: Malaysia
Sigma,
Nozzle allowable load of adjacent equipment is low and I cannot use the metallic expansion joint. Movement of the nozzle in left side equipment is about 30,40 mm in the vertical and radial direction, thus movement*stiffness of metallic expansion joint is higher than allowable load. What is the problem with the fabric expansion joint at temp 500?
Michael,
I think it is better to change EJ4 to Hinged type for the stability of the system. Also, the orientation of hinged should be in accordance with the picture. But the orientation of EJs are about 3-4 degrees and the use of spring support(spring can for under pipe) may be impossible, and I should use hanger. Do you have any advice on the design of the line?


Attachments
G2.jpg




Edited by NRAM (11/13/19 05:50 PM)

Top



Moderator:  Dave Diehl, Richard Ay 
Who's Online
0 registered (), 66 Guests and 1 Spider online.
Key: Admin, Global Mod, Mod
December
Su M Tu W Th F Sa
1 2 3 4 5 6 7
8 9 10 11 12 13 14
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31
Forum Stats
11721 Members
14 Forums
16089 Topics
72133 Posts

Max Online: 191 @ 11/16/19 10:39 AM
Top Posters (30 Days)
Michael_Fletcher 23
Sigma 13
vermaccio 12
Faizal K 8
Vanman 7