#55203 - 06/28/13 06:46 AM
Configuration Editor doesn't pop-up
|
Member
Registered: 10/29/12
Posts: 6
Loc: Mars
|
Hello,
When I start Configuration Editor its window doesn't pop-up. I see it hanging in the task manager and even on the task bar with other program windows. Can anyone help me out?
If the problem will be solved: can I change code year in the Configuration Editor (for example, ASME NC 1992 instead of 2010)?
|
Top
|
|
|
|
#55222 - 06/29/13 08:16 AM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
Did you move from a setup with two monitors to one monitor? Sometimes we see this, and Windows remembers the last position of the window. The position is saved in the Registry, and is likely off your screen. The only solution is to use REGEDIT, navigate down to "c2config" and delete that key.
What exact version of CAESAR II are you using? I'll give you the exact key (path) to delete.
You can't change "Code years". A specific version of CAESAR II supports a specific edition of the piping Codes.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
#55234 - 06/30/13 11:27 PM
Re: Configuration Editor doesn't pop-up
[Re: Richard Ay]
|
Member
Registered: 10/29/12
Posts: 6
Loc: Mars
|
We are using CAESAR II 2013 R1 (6.10.00.00228 Build 111130).
In other piping programs I have a possibility to change code edition. And you are saying I need an older CAESAR II to use previous code editions? Am I right? Older code editions is the client demand.
|
Top
|
|
|
|
#55246 - 07/01/13 08:54 PM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
All versions of CAESAR II support one Edition of any particular Piping Code.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
#55250 - 07/02/13 12:32 AM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 10/29/12
Posts: 6
Loc: Mars
|
So what about Configuration Editor problem? And under one version of particular code you mean the latest? Sorry if my questions seem stupid.
Edited by anatolii (07/02/13 12:38 AM)
|
Top
|
|
|
|
#55328 - 07/06/13 10:32 AM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
There are only two reasons I'm aware of that would prevent the Configuration window from appearing:
1) The associated DLLs and OCX files didn't register at install time. Assuming you have "Admin Rights", run the "netuserc2.bat" file in the \caesarii program directory to manually register these.
2) Flipping between single/dual monitors can sometimes cause Windows to same the screen position with non-existent coordinates. Try navigating into the CAESAR II registry branch and delete the key for "c2config". (Note, only that one key).
If these don't resolve the problem, open a Support Request on eCustomer.
The specific Code Editions a specific version of CAESAR II supports can be found in the Quick Reference Guide.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
#55341 - 07/07/13 11:56 PM
Re: Configuration Editor doesn't pop-up
[Re: Richard Ay]
|
Member
Registered: 10/29/12
Posts: 6
Loc: Mars
|
Thank you!
Deleting c2config branch in registry helped though I never used dual monitors.
And again about Code Editions: can you be more specific and tell me if I would need to use previous Code Edition than it's is supported by my current CAESAR II what should I do?
Edited by anatolii (07/07/13 11:57 PM)
|
Top
|
|
|
|
#55387 - 07/09/13 01:19 PM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
Restricting this to only B31.3:
CAESAR II v.5.30 conforms to (only) B31.3 2008. CAESAR II v.6.10 conforms to (only) B31.3 2010. CAESAR II v.7.00 will conform to (only) B31.3 2012.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
#61710 - 01/07/15 10:07 PM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 03/11/08
Posts: 32
Loc: Australia
|
Hi Richard,
I have similar problem here. Could you please give me a hand on how to sort this problem? I'm using ver 5.20
Thanks
|
Top
|
|
|
|
#61718 - 01/08/15 09:38 AM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
If you have followed and tried all of the suggestions above, and it still doesn't work, open a Support Request on Smart Support so the Technical Support group can assist you.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
#61726 - 01/08/15 02:49 PM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 03/11/08
Posts: 32
Loc: Australia
|
Hi Richard,
The problem is I couldn't find the c2config branch in version 5.20 registry.
|
Top
|
|
|
|
#61730 - 01/08/15 07:02 PM
Re: Configuration Editor doesn't pop-up
[Re: anatolii]
|
Member
Registered: 12/13/99
Posts: 6226
Loc: Houston, Texas, USA
|
Did the Configuration Module ever run on your machine? If you got to the CAESAR II program directory, run the netuserc2.bat file. This will register the necessary DLLs and may resolve the issue.
If this doesn't work, you need to talk to support, file that SR.
_________________________
Regards, Richard Ay - Consultant
|
Top
|
|
|
|
|
0 registered (),
40
Guests and
1
Spider online. |
Key:
Admin,
Global Mod,
Mod
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
|
|
|
|
|
12065 Members
14 Forums
16973 Topics
75151 Posts
Max Online: 303 @ 01/28/20 11:58 PM
|
|
|